.jpg){kind=icon}
.jpg){kind=icon}
-50%
LED Strip 24V-DC 10W/m SMD5050 IP68 20 meters Roll
SKU:B1502-BF
Shipping to Africa available
For any shipping requests to Africa, please contact our sales department at: comercial@barcelonaled.com
20 METERS ROLL OF 24V-DC 10W/M PLASTICIZED IP68 LED STRIPS
Novel 24V-DC IP68 silicone LED strip, built with SMD5050 chip, will allow you to make custom assemblies in longitudinal runs where the standard 12V or 24V strip is not enough, especially in installations beyond 10 linear meters.
Its construction, with a 12mm PCB and a 14mm siliconized coating, makes this LED strip the perfect solution for high quality and resistant outdoor installations. Its included waterproof connectors allow you to make the necessary splices quickly and easily. Its high quality silicone coating does not crack, does not yellow, ensuring its durability over time.
You will be able to light up to 40 meters, with a single power supply in the center, according to the following scheme:
IP68 degree of protection. One of the best quality LED strips on the market. Robust, without annoying flickering and with a homogeneous illumination in all meters that allows its installation. The SMD 5050 chip provides high intensity and durability. It can be cut on the cut marks, marked on the LED strips. Ultra-bright, with low power consumption and high heat dissipation.
These LED strips are waterproof, so they can be installed both outdoors and indoors. The installation of these LED strips is very simple and stands out for being able to offer a uniform LED lighting, using only one power supply in 40 meters. With a beam opening angle of 120 degrees.
Technical features:
- SMD5050 LED chip - 60 chips/meter.
- Warm white 2700K / Cool white 6000K / RGB
- Nominal power: 10W/meter
- Voltage: 24V
- Coil length: 20 meters
- IP68
- PCB width: 12mm
- Total width: 14mm including silicon coating
- Cutting distance: 100mm
- Frequency: 50/60 Hz
- Waterproof connectors included
- No self-adhesive included, staple / profile mounting.
Applications:
- Architectural lighting
- Building contours and canopies
- Decorative lighting of high humidity areas
- Contours of swimming pools, lakes and ponds
- Illumination of large illuminated signs
- Any installation requiring long runs at low voltage
Cable connection Model RGB:
- Cable Black Mark > + Positive
- Cable without Color Mark > Green Channel
- Cable with Red / (Brown) Mark > Red Channel
- Cable Blue Mark > Blue Channel
Nominal Voltage (V)
24V-DC
Power (W)
10
Power/m (W/m)
10
Kelvin (K)
3000
Beam angle (º)
120
Lifetime (h)
25000
IP
IP68
Dimensions (mm) Lxlxh
20000x12
Frequency (Hz)
50 - 60
Hue
Cool white
RGB
RGB
LED Type
SMD 5050
Dimmable
Yes
No. of chips/metre
60
Track width (mm)
12
Cutting distance (mm)
100
Use Outdoor
Yes
Temperature range
-20°C ~ +40°C
Adhesive
No
Energy efficiency class
A+ (2021)
Certificates
CE
ROHS
ROHS
Warranty
According to legal guarantee: 2 years
Questions
| P: Question: |
Good morning, I would like to know if it is dimmable Thank you |
|---|
| R: Answer: | All LED strips are dimmable with LED strip controllers, so is this model. |
|---|
| P: Question: | What is the minimum voltage at which the LED strip can operate without losing luminous intensity? |
|---|
| R: Answer: | The strip must operate at 24vdc |
|---|
| P: Question: | Good morning. I just received a B1502-RGB led strip. The connector has the following wires: brown, blue, black and colorless. Which line corresponds to each one of them (R G B and +)? |
|---|
| R: Answer: | Currently the connection is : Cable Black Mark > + Positive Cable No Color Mark > Green Channel Cable Red Mark (Brown) > Red Channel Cable Blue Mark > Blue Channel |
|---|
| P: Question: | I wanted to liven up a fountain and I had thought about LED strips: a short RGB section for a waterfall and a longer one in cold white (about 12mts) submerged. What will I need? |
|---|
| R: Answer: | The use of permanently submerged LED strips is not recommended. |
|---|
| P: Question: | Does it come with adhesive tape to stick it? |
|---|
| R: Answer: | This model does not have double-sided tape. |
|---|
| P: Question: |
Good afternoon. I need to know what sources and controllers I need to make two independent sections of 10 meters of this strip (B1502-RGB). They would go outdoors in a watertight box, I do not have much space, I would need them to be as compact as possible. Thanks |
|---|
| R: Answer: | You need a 24v power supply of at least 100W for each 10mts, you can use the SR-1009FA controllers with a SR-2819S controller (they are not for outdoor use). |
|---|
| P: Question: |
Good afternoon, my question is: I want to install an RGB led strip of 16.5 meters in a covered terrace in the form of "U", I will put it in an aluminum profile with opaque screen so that the distance between led is not very noticeable, and the power of the installation would be done approximately in the center, so we would have an output of about 8 meters on the left side and about 9 meters on the right, do you think it could illuminate enough room about 35/40 m2, without putting lamps? that advise me: 1º have this type of RGB strip directly to 220 V with length of 20 meters? and more or less 100 led / m. otherwise which advise me. 2nd if it has to be 12 or 24 V, can you recommend me the accessories I need, power supply, controller, controller, control, etc. if you provide me with the references will serve me for the order. Thank you very much in advance for your answer. Eduardo. |
|---|
| R: Answer: | Currently we do not have RGB models at 220v. For specific projects please contact comercial@barcelonaled.com |
|---|
| P: Question: |
Hello, I would like to know if this strip can be mounted on the crescent shaped profile, reference BPERF58X9. The profile admits 12 mm strips, but this IP68 strip seems to have 14 mm due to the protective silicone coating (I don't know how hard is that silicone or if it admits deformation). On the other hand, is it a problem to install the strip in an aluminum profile or due to the IP68 protection it could overheat? If it is not possible to mount it on a profile, what wall mounting method do you recommend? Thank you very much |
|---|
| R: Answer: | That profile model may be too tight for siliconized strips, you should look at a larger size option. Or siliconized staples. |
|---|
| P: Question: |
when it will be available LED Strip 24V-DC 10W/m SMD5050 IP68 20 meter roll Product reference:B1502-BF |
|---|
| R: Answer: | Please contact comercial@barcelonaled.com for product availability. |
|---|
| P: Question: | Good afternoon, I want to install a led strip on the terrace (outside, under the wing of the ledge of the fence (2 cm deep) to 1 meter high), the installation will be about 20 meters drawing a U, is it possible to feed it from one end ... I would like to be DC to put a dimmer and regulate the intensity and color if I decide to RGB, should I put IP68 ... there would be another alternative to put RGBW ... thank you very much. Thank you very much. |
|---|
| R: Answer: | It can be powered from one end, although there may be some light loss at the end. We do not have waterproof RGBW model, for outdoor use it is recommended IP65 and above. |
|---|
Page: 12
Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
