.jpg){kind=icon}
.jpg){kind=icon}
-15%
LED T8 120cm OSRAM 16.4W opal glass | SubstiTUBE STAR
SKU:O455382
Shipping to Africa available
For any shipping requests to Africa, please contact our sales department at: commercial@barcelonaled.fr
LED T8 Tube - 17W - 1200mm
The T8 crystal LED tube with 17W power consumption and high luminous flux of 1800 lumens. Instant on, no preheating time and no mercury. Thanks to the glass and plastic coating, it has a high light transmission (more than 90%), homogeneously distributed. With IP20 degree of protection for use in CCG or AC luminaires.
LED tubes perfect for placement in cold rooms, warehouses, garages, staircases, corridors, etc. Suitable for mono and duo operation with conventional power supply. High luminous efficiency of 109lm/W and optimum color rendering index, CRI>80. Available in neutral white (4000K).
Replaces conventional 1200mm fluorescent lamps.
With 200,000 ignition cycles and up to 30,000 hours of useful life. Dimensions of 603x267x267mm and a weight of only 100 grams.
- Base: G13.
- Luminous flux: 1800 lumens.
- Wide AC input range from 175V to 265V.
- Wide opening angle of 330 degrees.
- Glare-free opal cover.
- Short circuit and overheat protection.
- Length with socket but without pistons/connection: 1200mm.
- Socket diameter 26.7mm.
- Tube diameter: 25.8mm.
- Degree of protection IP20.
- Product weight: 190 grams.
T8 LED tube applications
- Direct replacement of conventional 60cm fluorescent tubes, general lighting.
- Perfect to illuminate closed parking lots, offices, stores, commercial galleries, kitchens, etc.
Installation in electronic ballasts
Step 1: Turn off the light from the main switchboard and verify that no electric current is coming.
Step 2: Remove the old tube (in this case there is no starter, since it is incorporated inside the electronic ballast).
Step 3: Disconnect the cables that enter the electronic ballast (no need to remove it, just disconnect it electrically).
Step 4: Choose one of the 2 tube holders to connect its 2 wires directly to the mains.
Step 5: We recommend marking the lamp holder where the connection has been made to facilitate the installation of the LED tube.
Installation of Ferromagnetic ballasts
Step 1: Turn off the main switchboard and check that there is no power supply.
Step 2: Take out the old tube and then the starter.
Step 3: Put the new LED starter bridge.
Step 4: Remove the capacitor or capacitor (to avoid overvoltage).
Step 5: Install the new LED tube.
Kelvin (K)
4000
Beam angle (º)
330
Socket
G13
Lifetime (h)
30000
IP
IP20
Dimensions (mm) Lxlxh
Ø26x1200
Hue
Neutral white
Detection angle (º)
No
Detection range (m)
No
Sensor
No
CRI
80-85
UGR
No
Dimmable
No
Driver
Internal
Tube type
T8
Orientable
No
Material
Plastic
Diffuser material
Crystal
Use Outdoor
Yes, with waterproof lamps
Temperature range
No
Frequency of use
Intensive
Energy efficiency class
A+
Certificates
CE
ROHS
ROHS
Warranty
3 years
Questions
| P: Question: | Can we connect this lamp directly to 220v? |
|---|
| R: Answer: | Yes, it's a bulb for 220V. |
|---|
| P: Question: | includes a choke? |
|---|
| R: Answer: | LED tubes do not use a starter, it is used only in fluorescent tubes. They have a jumper or fuse for use in installations where old wiring is reused. |
|---|
| P: Question: |
why does it have a choke? |
|---|
| R: Answer: | The LED tubes do not have a starter, they go directly to the 230Vac mains from the side indicated. The included starter is simply a bridge to take advantage of the wiring in some old installations fed from both sides in fluorescent systems. It is advisable to leave the installation correctly for LED tubes, simply unilateral connection, without ballasts or starters of previous systems. |
|---|
Page: 1
Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
