LED Tube T8 1500mm Glass LED Tube 22W Opal
LED Tube T8 1500mm Glass LED Tube 22W Opal
LED Tube T8 1500mm Glass LED Tube 22W Opal

LED Tube T8 150cm 24W high efficiency 140 LM/W

SKU:B4011-5-150BF
Colour temperature
Has superado el límite de unidades
In stock 7569 units
Data sheet

OPAL 150cm 24W Opal, SMD 2835, 230V-AC, angle 330º.

Power factor : 0.95

High efficiency 140 LM/W

Cool white Neutral white Warm white
24W 24W 22W
6000K 4000K 3000K
3455 lm 2917lm 2200 lm
Shipping to Africa available
public
For any shipping requests to Africa, please contact our sales department at:  comercial@barcelonaled.com

LED T8 150cm 24W 140 LM/W high power factor.

Replaces conventional 150cm / 58W fluorescent tubes.

T8 LED tube, equipped with high brightness SMD 2835 chip and high light transmittance (over 90%) glass and plastic coating, allows uniform light distribution.

  • Wide AC input range from 175V to 265V
  • High power factor up to 0.95
  • Wide opening angle (330º)
  • Glare-free opal coating
  • Short-circuit and overheat protection
  • Including starter jumper
  • Diameter Ø26mm

Equivalences:

  • LED tube T8 150cm 22W Warm white 3000K equivalent to T8 150cm fluorescent 58W/830
  • LED tube T8 150cm 24W Neutral white 4000K equivalent to T8 150cm fluorescent 58W/840 - 58W/845
  • LED Tube T8 150cm 24W Cool White 6000K equivalent to T8 150cm fluorescent 58W/860 - 58W/865

tubo led t8

Download the step by step installation guide from this link.

Installation in ferromagnetic ballasts:

Step 1: Turn off the light at the main switchboard and verify that no electric current is coming.

Step 2: Remove the old tube and then the starter.

Step 3: Put the new LED starter bridge (included with each tube).

Step 4: Remove the capacitor or capacitor (to avoid overvoltage).

Step 5: Install the new LED tube.

Installation in electronic ballasts:

Step 1: Turn off the light at the main electrical panel and verify that no electric current is coming.

Step 2: Remove the old tube (in this case there is no starter, as it is incorporated inside the electronic ballast).

Step 3: Disconnect the cables that enter the electronic ballast (no need to remove it, just disconnect it electrically).

Step 4: Choose one of the 2 tube holders to connect its 2 wires directly to the mains.

Step 5: We recommend to mark the lamp holder where the connection has been made to facilitate the installation of the LED tube.

  • If the installation contains a capacitor bank consult your specialized technician.

Applications:

  • General lighting, direct replacement of conventional 150cm fluorescent tubes.
  • Perfect for illuminating closed parking lots, offices, stores, commercial galleries, kitchens, etc.
  • Thanks to its angle, it is ideal for placement on walls.

tubo led t8 tubo led t8 tubo led t8

Nominal Voltage (V)
220 - 240 V/AC
Kelvin (K)
3000
4000
6000
Beam angle (º)
330
Socket
G13
Lifetime (h)
25000
IP
IP20
Dimensions (mm) Lxlxh
Ø26x1500
Frequency (Hz)
50 - 60
Hue
Cool white
Neutral white
Warm white
Sensor
No
Efficiency (Lm/w)
140
CRI
80-85
UGR
No
LED Type
SMD 2835
Dimmable
No
Power factor (cosφ)
0.95
Driver
Internal
Tube type
T8
Orientable
No
Material
Plastic
Diffuser material
Glass
Use Outdoor
Yes, with waterproof lamps
Frequency of use
Intensive
Energy efficiency class
D
Certificates
CE
ROHS
Warranty
According to legal guarantee: 2 years
Barcelona LED

Questions

P: Question: Hello,
I have an old installation of tubes, 58w fluorescent tubes with the typical ballasts, starters ,,,,
to install these led T8 tubes I understand that I do not have to touch anything but the starter, replacing it with the one you supply ?
I don't have to do anything else?

Thank you !
R: Answer: It depends on the installation, how many tubes go per ballast and the type of ballast.
The LED tubes go directly to the 220vac mains, they are only connected on one side marked non-input (L and N), without starter or ballasts of previous systems.
P: Question: when will you receive the cool white ones?
R: Answer: For availability, please contact comercial@barcelonaled.com.
P: Question: what is the problem in installing led tubes in installations with capacitor banks for reactive power?
R: Answer: If the installation is well compensated there should be no problems, but sometimes we have had incidents in led tubes where there are usually reactive power compensations. Probably resonance frequencies with non-linear and capacitive loads, harmonic current increases in the installation or non-led equipment in the same circuit that cause overvoltages at start-up.
P: Question: Hi, I just bought these fluorescents and my question is if they are dimmable by installing a dimmer. Thank you.
R: Answer: T8 LED tubes are not dimmable
P: Question: Good morning.
I want to replace some classic 58w/840 flurescent tubes with this model of led tube.
I would like to know if I will get the same amount of light, will they illuminate the same?
Thanks
R: Answer: If the equivalence in power of a 24W LED tube, 150cm is the equivalent of a 58W fluorescent tube. Remember that the LED tubes go directly to the mains and 220vac connected only by one side of the tube. Without ballasts and starters of the previous system.
P: Question: Hello good, does it contain a starter? I have to buy about 30 tubes for a community garage, and I would like to make sure that I have no problems with the purchase. Can you help me. Thanks
R: Answer: The LED T8 tubes do not use starter, ballasts, capacitors, or any components of previous systems, they are connected directly to the 220v mains by only one side marked as line and neutral. The tubes have a bridge that can be placed where before there was a starter to "reuse" the old installation and to be able to connect a cable on each side of the tube.
P: Question: Can you tell me what surface could illuminate each screen with 2 led tubes?
Recommended height?
Thank you very much.
R: Answer: The surface to be illuminated depends on the height and the amount of light needed depending on the room, place, and use of the area.
P: Question: Which led tube should I use to replace a classic Osram 58W/10 DAYLIGHT fluorescent? Thanks
R: Answer: It replaces the 150 cm led tube. The old watts are not the same as the led, you have to look for the measure.
P: Question: These tubes are suitable for watertight screens or are there other more convenient ones?
R: Answer: You can put the T8 tubes perfectly, and for more security the nanos tubes that are made of PVC.
P: Question: Hi, I just bought these fluorescents on your site, and I have a question, these fluorescents must be fed from both sides? Or they can be fed with phase and neutral only on one side?
Thanks
R: Answer: LED T8 tubes are only connected on one side.

Barcelona LED: Marc| 11/12/2019

Page: 12

Can't find the answer you're looking for?
Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form