.jpg){kind=icon}
.jpg){kind=icon}
LED Tube T8 60cm 9W High Efficiency 140LM/W
SKU:B4009-5-60BN
€2.44
Tax included
Shipping to Africa available
For any shipping requests to Africa, please contact our sales department at: comercial@barcelonaled.com
T8 LED Tube T8 9W 60cm high efficiency glass 140 LM/W
It replaces conventional 60cm / 18W fluorescent tubes.
The T8 LED tube, equipped with high brightness SMD 2835 chip and high light transmittance (more than 90%) glass and plastic coating, allows uniform light distribution.
- Wide AC input range from 175V to 265V
- High power factor up to 0.5
- Wide opening angle (330º)
- Glare-free opal coating
- Short-circuit and overheat protection
- Including starter jumper
- Diameter Ø26mm
Equivalences of T8 tube 60cm:
- T8 60cm LED tube T8 60cm LED 9W warm white 3000K is equivalent to T8 60cm fluorescent 18W/830
- LED Tube T8 60cm LED 9W neutral white 4000K equals T8 60cm fluorescent 18W/840 - 18W/845
- LED Tube T8 60cm LED 9W cool white 6500K equals T8 60cm fluorescent 18W/860 - 18W/865
Download the step by step installation guide from this link.
Installation in Ferromagnetic ballasts:
Step 1: Turn off the light at the main switchboard and verify that no electric current is coming.
Step 2: Take out the old tube and then the starter.
Step 3: Put the new LED starter bridge (included with each tube).
Step 4: Remove the capacitor or capacitor (to avoid overvoltage).
Step 5: Install the new LED tube.
Installation on Electronic ballasts:
Step 1: Turn off the light at the main electrical panel and verify that no electric current is coming.
Step 2: Remove the old tube (in this case there is no starter, as it is incorporated inside the electronic ballast).
Step 3: Disconnect the cables that enter the electronic ballast (no need to remove it, just disconnect it electrically).
Step 4: Choose one of the 2 tube holders to connect its 2 wires directly to the mains.
Step 5: We recommend marking the lamp holder where the connection has been made to facilitate the installation of the LED tube.
- If the installation contains a capacitor bank, please consult your specialized technician.
T8 LED tube applications:
- General lighting, direct replacement of conventional 60cm fluorescent tubes.
- Perfect for illuminating closed parking lots, offices, stores, commercial galleries, kitchens, etc.
- Thanks to its angle, it is ideal for placement on walls.
Nominal Voltage (V)
230
Lumens (Lm)
1260
Kelvin (K)
3000
4500
6000
4500
6000
Beam angle (º)
330
Socket
G13
Lifetime (h)
25000
IP
IP20
Dimensions (mm) Lxlxh
Ø26x600
Frequency (Hz)
50 - 60
Hue
Cool white
Neutral white
Warm white
Neutral white
Warm white
Detection angle (º)
No
Detection range (m)
No
Sensor
No
CRI
80-85
UGR
No
LED Type
SMD 2835
Dimmable
No
Power factor (cosφ)
0,5
Driver
Internal
Tube type
T8
Orientable
No
Material
Plastic
Diffuser material
Crystal
Use Outdoor
Yes, with waterproof lamps
Temperature range
No
Frequency of use
Intensive
Energy efficiency class
A+
Certificates
CE
ROHS
ROHS
Warranty
3 years
Questions
| P: Question: | The connection to the pipe is PHASE and NEUTRAL at the same end or the PHASE goes on one side and the Neutral on the other? |
|---|
| R: Answer: | You can see on the website that the T8 tubes are connected directly to 220vac network by only one side, marked as input L and N. |
|---|
| P: Question: |
Good morning, Would it be possible to obtain the data sheet with the light spectrum? Thank you very much |
|---|
| R: Answer: | It is being updated on the web at (Datasheet) or you can request the test report for the desired color temperature at comercial@barcelonaled.com. |
|---|
| P: Question: | Hello, why does the data sheet show 140lm/W and 99lm/W at the same time? |
|---|
| R: Answer: | Currently there are two references on the web series 3 (BC) and series 5 (BF,BN), it is the series 5 that has 140lm/W performance. |
|---|
| P: Question: | Can I replace a L18W/865 Osram from the kitchen with one of these tubes? I think that the current fluorescent holder does not have a starter. The current fluorescent is 59cm and this tube is 60cm, is it nomenclature or I have to look for another led tube? |
|---|
| R: Answer: | If you do not have a starter, your installation system is probably an electronic ballast. It must be removed to use LED tubes. The led tubes go directly to 220v only on one side of the tube. |
|---|
| P: Question: |
Hello, I have a fluorescent screen to which I put two led tubes and only disconnected the ballast and the old starter. I understand that I should continue without the ballast and only installing a starter for each tube ? Thank you. |
|---|
| R: Answer: | LED tubes do not need a ballast. If it is a ferromagnetic installation, we will only install the starter that is included in each tube. The installation in electronic ballasts does not need a starter, since it is incorporated inside. |
|---|
| P: Question: |
These tubes can be used in old screens, i.e. can I change this tube for one of the old ones in my own screen? |
|---|
| R: Answer: | Installation in ferromagnetic ballasts: Step 1: Turn off the light from the main electrical panel and check that no electric current is coming. Step 2: Remove the old tube and then the starter. Step 3: Put the new LED starter bridge (included with each tube). Step 4: Remove the capacitor or condenser (to avoid overvoltage) Step 5: Install the new LED tube. Installation in electronic ballasts: Step 1: Turn off the light from the main electrical panel and check that no electric current is coming. Step 2: Take out the old tube (in this case there is no starter, as it is incorporated inside the electronic ballast). Step 3: Disconnect the cables that enter the electronic ballast (no need to take it out, just disconnect electrically). Step 4: Choose one of the 2 tube holders to connect its 2 cables directly to the mains. Step 5: We recommend marking the lamp holder where the connection has been made to facilitate the installation of the LED tube. Barcelona LED: Marc| 10/01/2020 |
|---|
Page: 1
Your Question has been successfully sent our team. Thanks for question!
Ask a question
hide form
